Electrical

This page provides a "living document" of the Omni Commons electrical system. It is not necessarily completely accurate, though it strives to be, and is always important to get updated!

Primary Electrical System

• Main Panel (in Rise Above, room E of rear [48th St] exit)
  • Panel A (adjacent to main in Rise Above)
    • Panel AA (in Rise Above, on E wall adjacent to La Commune)
    • Panel AB (in basement next to N staircase)
    • Panel AC (in basement NW Kitchen Pantry, on E wall)
    • Panel AD (located upstage left in N corner of W wall of ballroom)
      • Panel ADA (in shower room on E wall)
    • Panel AE (located in storage room S of stage in N corner of W wall of ballroom)
  • Panel B (in Crow's Nest above stage in ballroom)
    • Panel BA (in rear ballroom balcony near S wall)
      • Panel BAA (on N wall of classroom between ballroom and La Commune)
        • Panel BAAA (on S wall of la commune by entrance book cashier table)
  • Panel C (in Disco Room at base of ladder to DJ booth)
  • Panel D (in Rise Above on E wall shared with La Commune)

Main Panel

Omni's main electrical panel

X = Disconnected

Label ->	Breaker #	Breaker #	<- Label
Panel B & Panel D 200amps	1	2
	3	4
Panel A 200amps	5	6
	7	8
X	9	10	Panel C 100amps
	11	12
Storage #5 / Trash Room	13	14	n/a
	15	16	n/a
Storage #5 / Trash Room	17	18	n/a
Counter Culture Labs (CCL) Closet	19	20	n/a
	21	22	n/a
n/a	23	24	n/a

Panel A

Panel A

X = Disconnected

200amps

Label ->	Breaker #	Breaker #	<- Label
Panel AA (La Commune)	1	21	Panel AE
	2	22
Panel AB	3	23	220V plug (rise above dryer) via Panel AA
	4	24
? Panel AC	5	25	Panel AD
	6	26
	7	27
	8	28
	9	29
Upstairs (cafe mezzanine) kitchen light / Upstairs (cafe mezzanine) bathroom lights / Exit Sign at top of W cafe mezzanine staircase	10	30	Sudo Room outlets on South Wall
X	11	31	X
Hood over oven in upstairs kitchenette (cafe mezzanine) / W Wall Kitchenette Outlet (R of sink) / W wall kichenette outlet (Above oven in alcove)	12	32
	13	33
	14	34
	15	35
	16	36	X
	17	37	Blue Classroom S wall outlets
2 TIL Office Lights (upstairs) / Front Door Exit Sign / Two Lights on Beam at entrance	18	38
Light fixture and outlets in Blue Classroom alcove on N wall	19	39
Upstairs kitchenette (cafe mezzanine) S wall outlets / W Wall Kitchenette Outlet (L of sink) / N wall kitchenette outlets (at entrance) / Outlets under bar on S Wall of Disco Room near S Wal of Kitchenette	20	40

Floorplans

• Panel Tree Diagram

  {Placeholder}

• Annotated Floorplan

  {Placeholder}

• 

  Unlabeled Floorplan (basis)

Documentation Protocol

Any building's electrical system is intended to serve the needs of the users of the building in a safe manner. However, we operate within constraints such as the historical developments of the electrical system, regulations, best practices, etc. In order to reduce ambiguity and risk, we must use a consistent documentation protocol throughout the system to understand and share knowledge of historical, current, and future uses.

Naming Convention

• Label the main electrical panel as "MAIN"
• Label the direct sub-panels of the main panel with a letter, e.g. "A", "B".
• Label each sub-panel that is connected to a first-tier sub-panel of the main panel.
  • "origin panel letter" + "sub-panel letter" + ... (for each sub-panel add another letter) ...
    • e.g. "AA" for the first sub-panel from panel "A"
    • e.g. "AAB" for the second sub-panel attached to panel "AA"
• For each circuit, label each outlet, switch, and load with:
  • the appropriate sub-panel name (described above) + "breaker number"
    • e.g. All the outlets in one room that are on the same circuit should be labeled "CA4" meaning the circuit is on breaker 4 on panel CA, which is the first panel originating from panel C that connects to the Main panel.
  • the draw on the curcuit
    • e.g. 20 amps

Here is the OLD breaker panel diagram

Protocol

• We are especially (not exclusively) updating our electrical system documentation on a room-by-room basis.
• As you work throughout Omni Commons, you should only use the system described above to map the electrical system.
• All other systems will be overridden.
• You can print this page and the building floorplans above in order to document the labeling you make on the actual outlets, panels, etc.
  • After labeling and writing on the printed building floorplan, deliver it to any member of the Building Working Group.